10.75 X 21 RMP™ Molle Backpack Insert

Molle Panel Backpack Insert RMP Tactical Bag Organizer

– Molle Panel Backpack Insert stays upright in the backpack

– Attach MOLLE style pouches to organize your gear

– Customize with Adhesive Backed Loop to accept Velcro Hook Pouches

– Use GMT backer plates to hard mount a variety of accessories

– Universal fit, check compatibility chart for sizing

– 0.25″ holes on edge for mounting with screws

– 1″ slots for attaching handles or mounting with 1″ webbing

Weapon mounts here

The Rigid Molle Panel was designed for a modular organization on a rigid platform that allows vertical organization within a backpack. The consistent positioning and customizable layout enhance quick access to your gear. When inserted into any bag, it gives you the tactical ability to organize your mission-critical gear on an interchangeable platform that can be swapped out or quickly reorganized as the mission changes.

Securing RMP inside Backpack

Making a velcro panel with 3m tape with an adhesive-backed loop to have a secure fit is a good way to secure. You can also attach elastic straps and d-rings to the side. While a lot of people will just put the molle panel backpack insert inside and leave it there.

For Recycled Firefighter Packs:

Slip the hydration bladder loop into the cutout at the top center of the RMP.

For Backpacks with Internal Webbing:

Some backpacks have MOLLE webbing sewn inside. You can loop a velcro one wrap, Velcro Cinch Strap, Web Dominator, or Grimloc through the backpack’s internal MOLLE webbing and secure the panel to the pack using one of those methods.

For backpacks with Internal Velcro Loop:

– Purchase “Low Profile Hook – Adhesive Backed – 3/4″ Width” from GMT.

– Ensure the Molle Backpack Insert is cleaned with an alcohol wipe and completely dry.

– Peel the backing off the adhesive-backed velcro tape and place the hook section onto the panel. Press it firmly into place, press further with a rolling pin, or place heavyweight onto the panel to compress and ensure full contact.

– Apply heat from a hairdryer to warm up the panel and the velcro hook tape, enabling the adhesive to “run” or liquefy enough to seep into the panel for a better bond.

– Optionally, use 3M Primer 94 to prime the surface before sticking the adhesive-backed velcro into place. This promotes higher adhesion to the panel.

For any backpack without internal MOLLE webbing:

Hydration Bladder Loop

– Secure the panel at the top of the internal main pocket by using a hydration bladder loop if available. Use Velcro one wrap or Grimloc.

Grommet / Chicago

– Punch a hole in the fabric and secure a grommet to prevent ripping. Use a Chicago screw to secure the panel to the grommet.

Adhesive-backed Velcro

To adhere the Adhesive-backed Velcro Hook tape to your RMP panel:

– Ensure the panel is cleaned with an alcohol wipe and completely dry.

– Peel the backing off the adhesive-backed velcro tape and place the hook section onto the panel. Press it firmly into place, press further with a rolling pin, or place heavyweight onto the panel to compress and ensure full contact.

– Apply heat from a hairdryer to warm up the panel and the velcro hook tape, enabling the adhesive to “run” or liquefy enough to seep into the panel for a better bond.

– Optionally, use 3M Primer 94 to prime the surface before sticking the adhesive-backed velcro into place. This promotes higher adhesion to the panel.

To adhere the Loop side adhesive backed velcro to the backpack:

– Once Velcro Hook has adhered to the Molle Backpack Insert, stick the velcro loop onto that strip on the panel as well, so it is perfectly lined up

– Flip your backpack inside out, so you get an unobstructed view of the interior back panel of the bag that the rigid molle panel will fit against

– Peel the plastic off the adhesive-backed velcro loop (leaving the velcro loop stuck in place on the RMP)

– Line up the entire RMP where you want it in the backpack and stick it down in place. Press firmly to ensure the Velcro Loop side has stuck to the bag, and then peel the panel/velcro hook away from the bag, careful to leave the velcro loop in place inside the bag.

– Press further with a rolling pin or place heavyweight onto the panel to compress and ensure full contact. Apply heat from a hairdryer to warm up the bag and the velcro loop tape, enabling the adhesive to “run” or liquefy enough to seep into the bag fabric for a better bond.

Universal Molle Compatibility

This molle panel backpack insert will fit any molle pouches or molle straps. You can even attach velcro to the panel and get exactly what you want . prefect for organizers and tactical people who what to add rigidity to their bags.

What can you attach to

First aid kit

Handguns for everyday carry

Survival items

Gloves

EDC

Phones

Attaching Holsters with Quick Detach Platforms on Molle Insert Panel

 

Set Backer Plate into punch out from the back of RMP panel at the desired location.
– Accessories with multiple backer plates may need the backer plates to be oriented properly for either vertical or horizontal mounting
– Pass screws through Female Receiver Plate and into tapped hole of the backer plate from the RMP panel’s front side, screw in to secure.
– Screw the Male Plate onto the Holster.
– If desired, mount additional Female Receiver Plates onto a belt loop, MOLLE webbing of bag or vest elsewhere, separate RMP panel in a vehicle, storage case, safe door, etc. Anywhere you mount additional Female Receiver Plates will allow you to quickly secure the piece of gear that has the Male Plate to that item. The same procedure can be used to attach any accessory that requires backer plates

molle backpack insert

molle backpack insert

molle backpack insert attaching pistol

molle backpack insert attaching pistol

molle backpack insert attaching pistol

 

 

Attaching MOLLE Pouches

Standard MOLLE Pouch Attachment to Grey Man Tactical Rigid molle backpack insert

Standard MOLLE Pouch Attachment to Grey Man Tactical Rigid molle backpack insert

  
  
 

Upgrading to accept Velcro Hook/Loop Pouches

 

To upgrade any Molle Backpack Insert RMP to accept Hook backed pouches, morale patches, or accessories, follow the below steps:
To adhere the Adhesive-backed Velcro Loop tape to your RMP panel:
– Purchase “Low Profile Loop – Adhesive Backed – 1″ Width” from GMT.
– Ensure the panel is cleaned with an alcohol wipe and completely dry.
– Peel the backing off the adhesive-backed velcro tape and place the loop section onto the panel. Press it firmly into place, press further with a rolling pin, or place heavyweight onto the molle panel to compress and ensure full contact.
– Apply heat from a hairdryer to warm up the panel and the velcro, enabling the adhesive to “run” or liquefy enough to seep into the panel for a better bond.
– Optionally, use 3M Primer 94 to prime the surface before sticking the adhesive-backed velcro into place. This promotes higher adhesion to the panel.